Home > Torque Solution

Torque Solution

Sort By:
Page of 10
Torque Solution Adjustable Thrust Arm Bushing Kit: Porsche Torque Solution Engine Mount Kit: Porsche 911 1998-11 Torque Solution Drive Shaft Carrier Bearing Support Bushings: Mitsubishi 3000GT / Dodge Stealth
MSRP $213.75
MSRP $379.99
MSRP $47.49
Torque Solution Adjustable Thrust Arm Bushing Kit: Porsche Torque Solution Engine Mount Kit: Porsche 911 1998-11 Torque Solution Drive Shaft Carrier Bearing Support Bushings: Mitsubishi 3000GT / Dodge Stealth
Torque Solution Adjustable Thrust Arm Bushing Kit
Applications: 996TT/GT2/GT3/C2/C4/C4S & GT3 Cup 997TT/GT2/GT3 & RS/C2/C4 and GT3 Cup
 
Torque Solution adjustable thrust arm bushing kit replaces the factory, rubber bushings on the wheel-end of the control arms with a billet aluminum bushing, this will allow for better handling and most important also allows for the adjustment of
caster.Replacement thrust arm bushings significantly improve the handling and response from your 996 or 997 suspension.

Can be used in all lower stock control arms as well as adjustable Porsche Motorsport Cup arms. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration. Helps minimize the soft feeling on the multilink factory suspension without major added in cabin road noise..  A great improvement for street cars and a must for anyone taking their car to the track. Your cars alignment on Factory equipment will change the 1st few laps around the track without solid thrust bushings to keep things in check.

Sold in kits of 4 to replace front or rear lower control arm bushings.

Fitment: 996TT/GT2/GT3/C2/C4/C4S & GT3 Cup
997TT/GT2/GT3 & RS/C2/C4 and GT3 Cup

 
Torque Solution Engine Mount Kit
Applications: Porsche  996TT/GT2/GT3/C2/C4/C4S & GT3 Cup 997TT/GT2/GT3 & RS/C2/C4 and GT3 Cup
 
Torque Solution Porsche Engine Mounts are designed to limit the amount of Engine movement from side to side which throws off the balance of the car under load. The factory mounts allow the engine to move which gives the feeling of a sloppy drivetrain. The mounts will give the car a more direct feel and more precise driver input to the vehicle. You can expect a much better feel under Braking, Acceleration, & lateral G's. While typically most " Race Cars " use a SOLID MOUNT, this solution is less harsh and still maintains better control of the engine movement without the issue of Solid Mount Vibration. The next issue with Solid mounts is the transmission of noise from the chassis to the knock sensor on the engine which can result in a tuning nightmare. These mounts will not affect knock sensor like solid mounts do..

*Polyurethane Pictured in BLUE to show design. You will receive in all black.
 
- Eliminates wheel hop / traction loss
- Improved 60fts / e.t's
- Made out of lightweight 6061-T6 billet aluminum
- Black anodized / Torque Solution Laser engraved
- 75A durometer bushings
- Life Time Warranty
- Made in USA
 
Torque Solution DriveShaft Carrier Bearing Support Bushings
Applications: Mitsubishi 3000 GT / Dodge Stealth 
 
Torque Solution Drive Shaft Center Support Bushings will replace the OEM Rubber mounts with Delrin Polymer pieces. Doing so will allow for reduced wheel hop, improved acceleration and better E.T's. The mounts keep the propeller shaft from moving under hard acceleration, stopping and turning giving you optimal performance 100% of the time.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight Delrin
-Less NVH than 6061 Billet
-Street and track torture tested
-Life Time Warranty
-Made in USA
 
 
Torque Solution Shorty Billet Antenna : Mitsubishi Lancer Sportback 2008-11 Torque Solution Shorty Billet Antenna : SUBARU Wrx / Sti 2008-13 Torque Solution Shorty Billet Antenna : Mitsubishi Evolution X 2008-12 ( Excluding MR )
MSRP $22.79
MSRP $22.79
MSRP $22.79
Torque Solution Shorty Billet Antenna : Mitsubishi Lancer Sportback 2008-11 Torque Solution Shorty Billet Antenna : SUBARU Wrx / Sti 2008-13 Torque Solution Shorty Billet Antenna : Mitsubishi Evolution X 2008-12 ( Excluding MR )
Torque Solution Shorty Antanna
Applications: Mitsubishi Lancer Sportback 2008-2011
 
Replace your long factory antenna with our billet shorty antenna,Giving you a new style to your car. 
 
- 2 inch Tall
- Installs in under 2 minutes
- Made out of lightweight 6061-T6 billet aluminum
- Black anodized / Torque Solution Laser engraved
- Life Time Warranty
- Made in USA
 
 
Torque Solution Shorty Billet Antanna
Applications: Subaru Wrx & Sti 2008-2011
 
Replace your long factory antenna with our billet shorty antenna,Giving you a new style to your car.  
 
•3.8 inch Tall
• Installs in under 2 minutes
• Made out of lightweight 6061-T6 billet aluminum
• Black anodized / Torque Solution Laser engraved
• Life Time Warranty
• Made in USA

 
Torque Solution Shorty Antanna
Applications: Mitsubishi Evolution X 2008-2011
 
Replace your long factory antenna with our billet shorty antenna. Giving you a new style to your car.

* If your antenna base has a MALE stud coming out of it.. this WILL NOT WORK on your car. Check before ordering.
 
• 3.8 inch Tall
• Installs in under 2 minutes
• Made out of lightweight 6061-T6 billet aluminum
• Black anodized / Torque Solution Laser engraved
• Life Time Warranty
• Made in USA
Torque Solution Shorty Billet Antenna : Mitsubishi Evolution GSR 2008-12 ( EXCLUDING MR ) Torque Solution Stubby Billet Antenna: Honda S2000 Torque Solution Stubby Billet Antenna: Mitsubishi Lancer Evolution 2003+
MSRP $22.79
MSRP $22.79
MSRP $22.79
Torque Solution Shorty Billet Antenna : Mitsubishi Evolution GSR 2008-12 ( EXCLUDING MR ) Torque Solution Stubby Billet Antenna: Honda S2000 Torque Solution Stubby Billet Antenna: Mitsubishi Lancer Evolution 2003+
Torque Solution Shorty Antanna
Applications: Mitsubishi Evolution GSR 2008-2011
 
Replace your long factory antenna with our billet shorty antenna,Giving you a new style to your car.

* If your antenna base has a MALE stud coming out of it.. this WILL NOT WORK on your car. Check before ordering.
 
• 2 inch Tall
• Installs in under 2 minutes
• Made out of lightweight 6061-T6 billet aluminum
• Black anodized / Torque Solution Laser engraved
• Life Time Warranty
• Made in USA

 
Torque Solution Shorty Antenna
Applications: Honda S2000 ALL
 
Replace your long factory antenna with our billet shorty antenna,Giving you a new style to your car.
 
- 3.8" inch Tall
- Installs in under 2 minutes
- Made out of lightweight 6061-T6 billet aluminum
- Black anodized / Torque Solution Laser engraved
- Life Time Warranty
- Made in USA
Torque Solution Shorty Antenna
Applications: Mitsubishi Lancer Evolution 2003+
 
Replace your long factory antenna with our billet shorty antenna, Giving you a new style to your car.
 
- 3.8" inch Tall
- Installs in under 2 minutes
- Made out of lightweight 6061-T6 billet aluminum
- Black anodized / Torque Solution Laser engraved
- Life Time Warranty
- Made in USA
Torque Solution Stubby Billet Antenna Torque Solution Shorty Billet Radio Antenna (BLACK): Universal Torque Solution Shorty Billet Radio Antenna
MSRP $22.79
MSRP $18.99
MSRP $18.99
Torque Solution Stubby Billet Antenna Torque Solution Shorty Billet Radio Antenna (BLACK): Universal Torque Solution Shorty Billet Radio Antenna
Torque Solution Shorty Antenna
 
Replace your long factory antenna with our billet shorty antenna, Giving you a new style to your car.
 
- 3.8" inch Tall
- Installs in under 2 minutes
- Made out of lightweight 6061-T6 billet aluminum
- Black anodized / Torque Solution Laser engraved
- Life Time Warranty
- Made in USA
Torque Solution Shorty Antanna
Applications: UNIVERSAL
 
Replace your long factory antenna with our billet shorty antenna. Giving your car new styling.
 
• 3.8" Tall
• Installs in under 2 minutes
• Made out of lightweight 6061-T6 billet aluminum
• Black Anodized
• Life Time Warranty
• Made in USA
Torque Solution Shorty Antanna
Applications:
 
Replace your long factory antenna with our billet shorty antenna,Giving you a new style to your car. 
 
• 2 inch Tall
• Installs in under 2 minutes
• Made out of lightweight 6061-T6 billet aluminum
• Black  or Silver anodized / Torque Solution Laser engraved
• Life Time Warranty
• Made in USA
Torque Solution Shifter Base Bushing Kit: Mitsubishi Evo X 2008-12 Torque Solution Shifter Base Bushing Kit: Mitsubishi Lancer 2008-12 Torque Solution Shifter Base Bushing Kit: Mitsubishi Eclipse GT 2006-10
MSRP $25.64
MSRP $25.64
MSRP $25.64
Torque Solution Shifter Base Bushing Kit: Mitsubishi Evo X 2008-12 Torque Solution Shifter Base Bushing Kit: Mitsubishi Lancer 2008-12 Torque Solution Shifter Base Bushing Kit: Mitsubishi Eclipse GT 2006-10
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Evo X 2008-2012

Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points.
 
• Cnc machined 6061-T6 billet aluminum
• Installs in under 30 minutes
• Life Time Warranty
• Made in USA
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Lancer 2008-2012
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment. 
 
• Cnc machined 6061-T6 billet aluminum
• Installs in under 30 minutes
• Life Time Warranty
• Made in USA
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Eclipse GT & GS 2006-2010
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
• Cnc machined 6061-T6 billet aluminum
• Installs in under 30 minutes
• Life Time Warranty
• Made in USA
Torque Solution Shifter Base Bushing Kit: Mitsubishi Evolution Vll-IX 2001-06 Torque Solution Shifter Base Bushing Kit: Lancer 2001-07 Torque Solution Shifter Base Bushing Kit: Mitsubishi 3000 GT
MSRP $25.64
MSRP $25.64
MSRP $25.64
Torque Solution Shifter Base Bushing Kit: Mitsubishi Evolution Vll-IX 2001-06 Torque Solution Shifter Base Bushing Kit: Lancer 2001-07 Torque Solution Shifter Base Bushing Kit: Mitsubishi 3000 GT
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Evolution Vll-IX 2001-2006
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA
 
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Lancer 2001-2007
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
Cnc machined 6061-T6 billet aluminum
Installs in under 30 minutes
Black anodized
Life Time Warranty
Made in USA
 
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi 3000 GT
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
• Cnc machined 6061-T6 billet aluminum
• Installs in under 30 minutes
• Black anodized
• Life Time Warranty
• Made in USA
Torque Solution Shifter Base Bushing Kit: Dodge Stealth 1991-97 Torque Solution Shifter Base Bushing Kit: Honda Civic ALL 06-12 Torque Solution Shifter Base Bushing Kit: Honda Civic Si 2002-05
MSRP $25.64
MSRP $25.64
MSRP $25.64
Torque Solution Shifter Base Bushing Kit: Dodge Stealth 1991-97 Torque Solution Shifter Base Bushing Kit: Honda Civic ALL 06-12 Torque Solution Shifter Base Bushing Kit: Honda Civic Si 2002-05
Torque Solution Shifter Base Bushing Kit
Application: Dodge Stealth 1991-1996
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
  
• Cnc machined 6061-T6 billet aluminum
• Installs in under 30 minutes
• Black anodized
• Life Time Warranty
• Made in USA 
Torque Solution Shifter Base Bushing Kit
Application: Honda Civic & Civic Si 2006-2012
 
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA
Torque Solution Shifter Base Bushing Kit
Application: Honda Civic Si Only 2002-2005
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
  
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA 
Torque Solution Shifter Base Bushing Kit: Honda Civic 2001-2005 Torque Solution Shifter Base Bushing Kit: Acura Rsx Type S 2002-06 Torque Solution Shifter Base Bushing Kit: Acura Tsx 2002-08
MSRP $25.64
MSRP $25.64
MSRP $25.64
Torque Solution Shifter Base Bushing Kit: Honda Civic 2001-2005 Torque Solution Shifter Base Bushing Kit: Acura Rsx Type S 2002-06 Torque Solution Shifter Base Bushing Kit: Acura Tsx 2002-08
Torque Solution Shifter Base Bushing Kit
Application: Honda Civic (MT) 2001-2005
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
  
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA 
Torque Solution Shifter Base Bushing Kit
Application: Acura Rsx  & Type S 2002-2006
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yields improved shifting feel and characteristics for years of enjoyment.
 
  
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA 
Torque Solution Shifter Base Bushing Kit
Application: Acura Tsx 2002-2008
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yeilds improved shifting feel and characteristics for years of enjoyment.
 
  
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA 
Torque Solution Shifter Base Bushing Kit: Mitsubishi Eclipse 1990 ONLY Torque Solution Shifter Base Bushing Kit: Mitsubishi Eclipse Talon Laser 91-94 Torque Solution Shifter Base Bushing: Mitsubishi Eclipse 2G 1995-1999
MSRP $25.64
MSRP $25.64
MSRP $25.64
Torque Solution Shifter Base Bushing Kit: Mitsubishi Eclipse 1990 ONLY Torque Solution Shifter Base Bushing Kit: Mitsubishi Eclipse Talon Laser 91-94 Torque Solution Shifter Base Bushing: Mitsubishi Eclipse 2G 1995-1999
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Eclipse 1990 ONLY
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yields improved shifting feel and characteristics for years of enjoyment.
 
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA
 
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Eclipse 1991-1994
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yields improved shifting feel and characteristics for years of enjoyment.
 
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA
 
Torque Solution Shifter Base Bushing Kit
Application: Mitsubishi Eclipse 2G 1995-1999
 
Torque Solution shifter base bushing kit replaces the OEM rubber bushings on the bottom of the shifter providing a more stable shifter platform and mounting points. This yields improved shifting feel and characteristics for years of enjoyment.
 
- Cnc machined 6061-T6 billet aluminum
- Installs in under 30 minutes
- Black anodized
- Life Time Warranty
- Made in USA
Torque Solution Exhaust Mount Kit: BMW E92 M3 2007+ Torque Solution Billet Engine Mounts: Chevrolet Camaro 2010+ Torque Solution Rear Differential Bushings: Chevrolet Camaro 2010+
MSRP $42.74
MSRP $280.25
MSRP $99.74
Torque Solution Exhaust Mount Kit: BMW E92 M3 2007+ Torque Solution Billet Engine Mounts: Chevrolet Camaro 2010+ Torque Solution Rear Differential Bushings: Chevrolet Camaro 2010+
Torque Solution Exhaust Mount
Applications: BMW E92 M3 2007+
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Replace your worn out cracked mounts.. Great compliment to any exhaust kit. They fit most cars, please check your car first.
 
-12mm Long X 4
-Eliminates Exhaust Movement
-Made From high grade polyurethane
-Street and track torture tested
-75A durometer
-Life Time Warranty
-Made in USA
Torque Solution Engine Mounts
Applications: Chevrolet Camaro 2010+
 
All Torque Solution engine mounts are made with both quality and performance in mind. These mounts are a direct replacement for the OEM factory mounts. OEM mounts are made of sub-par material with rubber bushings that are infamous for deteriorating, cracking, and tearing over time. Heavy racing or spirited driving tends to speed up that process. Torque Solution has you have covered! Our mounts are made out of high grade 6061 billet aluminum material for weight savings and polyurethane bushings for long life and consistent performance. This combination allows the wasted energy to be transferred to the wheels where its needed for optimal performance.
 
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-1000HP+ and 7sec e.t. torture tested
-Black anodized
-85A durometer bushings ( Not Solid )
-LifeTime Warranty
-Made in USA
Torque Solution Rear Differential Mount Inserts
Applications: Chevrolet Camaro 2010+
 
All Torque Solution rear differential mounts are made with both quality and performance in mind.  OEM mounts are made of sub-par material with rubber bushings that are infamous for deteriorating, cracking, and tearing over time. Heavy racing or spirited driving tends to speed up that process. Torque Solution has you covered! Our pins are made out of high grade 6061 billet aluminum material for weight savings and polyurethane bushings for long life and consistent performance.

By replacing them with these harder Polyurethane units you are able to get rid of the unwanted slop and flexing of the stock units which allows for the power to go into rotating the tires, instead of flexing the rubber. Giving you better feedback, sharper response, more predictability on throttle input, along with eliminating annoying clunking during hard shifts.
 
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-1000HP+ and 7sec e.t. torture tested
-Black anodized
-85A durometer bushings ( Not Solid )
-LifeTime Warranty
-Made in USA
Torque Solution Front & Rear Engine Mount Combo: Cobalt SS 2005-10 Torque Solution Front Engine Mount: Cobalt SS 2005-2010 Torque Solution Rear Engine Mount: Cobalt SS 2005-2010
MSRP $256.49
MSRP $131.09
MSRP $151.51
Torque Solution Front & Rear Engine Mount Combo: Cobalt SS 2005-10 Torque Solution Front Engine Mount: Cobalt SS 2005-2010 Torque Solution Rear Engine Mount: Cobalt SS 2005-2010
Torque Solution Engine Mounts
Applications: Chevy Cobalt SS 2005-2010
 
Torque Solution is proud to announce our new billet engine mounts for the chevy cobalt ss.These mounts are made of high quality billet aluminum material machined to precise tolerances. The heart of the mounts are made of high grade polyurethane material. These combination's of materials and measurements allow for unmatched performance and reliability.For street and race applications. Some vibration noticeable..
 
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•Street and track torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
Torque Solution Engine Mounts
Applications: Chevy Coablt SS 2005-2010
 
Torque Solution is proud to announce our new billet engine mounts for the chevy cobalt ss.These mounts are made of high quality billet aluminum material machined to precise tolerances. The heart of the mounts are made of high grade polyurethane material. These combination's of materials and measurements allow for unmatched performance and reliability.For street and race applications. Some vibration noticeable..
 
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•Street and track torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
Torque Solution Engine Mount
Applications: Chevy Coablt SS 2005-2010
 
Torque Solution is proud to announce our new billet engine mounts for the chevy cobalt ss.These mounts are made of high quality billet aluminum material machined to precise tolerances. The heart of the mounts are made of high grade polyurethane material. These combination's of materials and measurements allow for unmatched performance and reliability.For street and race applications. Some vibration noticeable..
 
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•Street and track torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
Torque Solution Engine Mount Inserts: Dodge Caliber 2006-11 Torque Solution Engine Mount Inserts: Dodge Caliber 2006-11 Torque Solution Upper Engine Mount: Dodge Neon 2000-05
MSRP $52.24
MSRP $103.54
MSRP $104.49
Torque Solution Engine Mount Inserts: Dodge Caliber 2006-11 Torque Solution Engine Mount Inserts: Dodge Caliber 2006-11 Torque Solution Upper Engine Mount: Dodge Neon 2000-05
Torque Solution Engine Mount Incerts
Applications: Dodge Caliber 2006-2011
 
Torque Solution polyurethane engine mount inserts that replace the inner rubber material of the OEM Dodge Caliber engine mounts.Each mount includes 2 half's and a center steel sleeve. These give you improved traction and reduced wheel hop without to much vibration. Bushings come with a lifetime warranty through Torque Solution. Fits both drivers side and passenger side.
       
                    
  • Eliminates wheel hop / traction loss
  • Improved 60fts / e.t's Street and track torture tested
  • 75A durometer bushings
  • Life Time Warranty
  • Made in USA
Torque Solution Engine Mount Incerts
Applications:
Dodge Caliber 2006-2011
 
Torque Solution is proud to announce our new billet engine mounts for the Saturn ION Red Line . These mounts are made of high quality billet aluminum material machined to precise tolerances. The heart of the mounts are made of high grade polyurethane material. These combination's of materials and measurements allow for unmatched performance and reliability.For street and race applications. Some vibration noticeable..
 
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Street and track torture tested
•75A durometer bushings
•Life Time Warranty
•Made in USA
 
Torque Solution Engine Mount
Applications: Dodge Neon 2000-2005
 
This mount in particular is the SRT-4 and Neon TOP engine mount. This mount is made out of the same high grade billet aluminum material as that all our mounts are made out of. Coupled with the polyurethane inserts and machined pins you will not only have a great looking mount for that engine bay but one that performs just as well. Lightest mounts on the market! These mounts are on the fastest World Challenge Neon SRT-4's in the country.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
 
Torque Solution Billet Aluminum Lower Engine Mount: Dodge Neon 2000-05 Torque Solution Billet Aluminum Engine Mount Combo: Dodge Neon 2000-05 Torque Solution Billet Aluminum Upper Engine Mount: Dodge Neon SRT-4 2003-05
MSRP $109.24
MSRP $193.33
MSRP $104.49
Torque Solution Billet Aluminum Lower Engine Mount: Dodge Neon 2000-05 Torque Solution Billet Aluminum Engine Mount Combo: Dodge Neon 2000-05 Torque Solution Billet Aluminum Upper Engine Mount: Dodge Neon SRT-4 2003-05
Torque Solution Engine Mount
Applications: Dodge Neon 2000-2005
 
This mount in particular is the SRT-4 and Neon lower engine mount. This mount is made out of the same high grade billet aluminum material as that all our mounts are made out of. Coupled with the polyurethane inserts and machined pins you will not only have a great looking mount for that engine bay but one that performs just as well. Lightest mounts on the market! These mounts are on the fastest World Challenge Neon SRT-4's in the country.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Engine Mounts
Applications: Dodge Neon 2000-2005
 
These engine mounts replace the OEM top and lower engine mounts. This combination will reduce 90% of wheel hop and engine movement to improve shifting, traction, and prevent damage to the intercooler hoses and exhaust systems due to excessive engine movement. These mounts have less vibrations when compared too the other aftermarket mounts. Take a look at the amount of urethane we use on each mount. We use 50% more urethane then all out competitors. These are the same mounts in the fastest world challenge Neon SRT-4's in the world.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Engine Mount
Applications: Dodge Neon Srt-4 2000-2005
 
This mount in particular is the SRT-4 and Neon TOP engine mount. This mount is made out of the same high grade billet aluminum material as that all our mounts are made out of. Coupled with the polyurethane inserts and machined pins you will not only have a great looking mount for that engine bay but one that performs just as well. Lightest mounts on the market! These mounts are on the fastest World Challenge Neon SRT-4's in the country.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
 
Torque Solution Billet Aluminum Lower Engine Mount: Dodge Neon SRT-4 2003-05 Torque Solution Billet Aluminum Transmission Mount: Dodge Neon SRT-4 2003-05 Torque Solution Billet Aluminum Engine Mount Combo: Dodge Neon SRT-4
MSRP $109.24
MSRP $104.50
MSRP $193.33
Torque Solution Billet Aluminum Lower Engine Mount: Dodge Neon SRT-4 2003-05 Torque Solution Billet Aluminum Transmission Mount: Dodge Neon SRT-4 2003-05 Torque Solution Billet Aluminum Engine Mount Combo: Dodge Neon SRT-4
Torque Solution Engine Mount
Applications: Dodge Neon Srt-4 2000-2005

 
This mount in particular is the SRT-4 and Neon lower engine mount. This mount is made out of the same high grade billet aluminum material as that all our mounts are made out of. Coupled with the polyurethane inserts and machined pins you will not only have a great looking mount for that engine bay but one that performs just as well. Lightest mounts on the market! These mounts are on the fastest World Challenge Neon SRT-4's in the country.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Engine Mount
Applications: Dodge Neon SRT-4 2000-2005
 
This mount replaces existing OEM transmission mount.The transmission mount is made out of high grade billet aluminum material with urethane material for the bushings. With the addition of the is mount you will see and feel an improvement with wheel hop being reduced and better traction. This is the lightest transmission mount on the market and can be seen on the fastest World Challenge SRT-4's in the world. Get what the pro's have at a price you can afford!
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•Street and track torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
Torque Solution Engine Mounts
Applications: Dodge Neon Srt-4 2000-2005

 
These engine mounts replace the OEM top and lower engine mounts. This combination will reduce 90% of wheel hop and engine movement to improve shifting, traction, and prevent damage to the intercooler hoses and exhaust systems due to excessive engine movement. These mounts have less vibrations when compared too the other aftermarket mounts. Take a look at the amount of urethane we use on each mount. We use 50% more urethane then all out competitors. These are the same mounts in the fastest world challenge Neon SRT-4's in the world.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Billet Aluminum Engine Mount Kit: Dodge Neon Srt-4 2003-05 Torque Solution Front Engine Mount: Mitsubishi Eclipse Laser / Talon 1990-94 Torque Solution DSM Rear Subframe Bushings: 2G Mitsubishi Eclipse / Talon AWD 1995-1999
MSRP $291.64
MSRP $104.49
MSRP $123.49
Torque Solution Billet Aluminum Engine Mount Kit: Dodge Neon Srt-4 2003-05 Torque Solution Front Engine Mount: Mitsubishi Eclipse Laser / Talon 1990-94 Torque Solution DSM Rear Subframe Bushings: 2G Mitsubishi Eclipse / Talon AWD 1995-1999
Torque Solution Engine Mounts
Applications: Dodge Neon Srt-4 2000-2005

 

Torque Solution is proud to offer the best complete engine mount set available for the Dodge Neon SRT-4. All mounts are made out of high grade billet aluminum material machined to the tightest tolerances. All the mounts bushings are made with 50% more urethane giving you the least amount of vibrations when compared to the competitors. These engine mounts are the lightest on the market. They can be seen on the fastest World Challenge Neon SRT-4's in the world. Wheel hop is notorious for snapping axles. Consider that a thing of the past. This combination of mounts will eliminate wheel hop giving you optimal traction under the harshest of conditions while saving your axles.These are the same mounts in the fastest world challenge Neon SRT-4's in the world.

 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Engine Mount
Applications: 
Mitsubishi Eclipse / Laser / Talon 1990-94
 
Torque Solution mounts are made of high quality billet aluminum material machined to precise tolerances. The heart of the mounts are made of high grade polyurethane material. These combination's of materials and measurements allow for unmatched performance and reliability.For street and race applications. Some vibration noticeable..
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight 6061-T6 billet aluminum
-Street and track torture tested
-Black anodized / Torque Solution Laser engraved
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Rear Subframe Bushing
Applications:  Eclipse 1995-1999 / Talon 1995-1998

Torque Solution continues to push the limits of high performance aftermarket products with our "NEW" Rear Subframe Bushings. This system was designed to reduce movement of the rear subframe. This helps to improve transmission feedback when shifting, and gives the car a more solid feel under hard acceleration. Developed to perform under the most extreme conditions, our Urethane Components bridge the gap between ordinary rubber and cheap plastics used in current aftermarket shifter bushings by offering a unique urethane specifically chosen by Torque Solution engineers to ensure product performance and reliability. All this makes it easy for us to stand behind our products with a lifetime warranty.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Street and track torture tested
-75A durometer bushings
-Life Time Warranty
-Made in USA
Torque Solution Drive Shaft Carrier Bearing Support Bushings: Mitsubishi Eclipse 1990-99 Torque Solution Exhaust Mount Kit: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Exhaust Mount: 9 mm
MSRP $47.49
MSRP $47.49
MSRP $8.55
Torque Solution Drive Shaft Carrier Bearing Support Bushings: Mitsubishi Eclipse 1990-99 Torque Solution Exhaust Mount Kit: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Exhaust Mount: 9 mm

Torque Solution Drive Shaft Carrier Bearing Support Bushings
Applications: 1990�1994 (1G) Mitsubishi Eclipse, Eagle Talon Tsi and Plymouth Laser Rs 1995�1999 (2G) Mitsubishi Eclipse Gsx
 

Torque Solution Drive Shaft Center Support Bushings will replace the OEM Rubber mounts with Delrin Polymer pieces. Doing so will allow for reduced wheel hop, improved acceleration and better E.T's. The mounts keep the propeller shaft from moving under hard acceleration, stopping and turning giving you optimal performance 100% of the time.
 
-Eliminates wheel hop / traction loss
-Improved 60fts / e.t's
-Made out of lightweight Delrin
-Less NVH than 6061 Billet
-Street and track torture tested
-Black anodized
-Life Time Warranty
-Made in USA
 
Torque Solution Exhaust Mount Kit
Applications: Mitsubishi  Evolution VII-IX 2001-2006 
 
Torque Solution exhaust mounts are made from a high grade Urethane.Our exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits.
 
Direct Replacement
 
•Eliminates Exhaust Movment 
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
 
 
Torque Solution Exhaust Mount
Applications:
 9 MM
 
Our exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust mount: 10 mm Torque Solution Exhaust Mount: 12 mm Torque Solution Exhaust Mount: 12 mm Long
MSRP $8.55
MSRP $8.55
MSRP $9.50
Torque Solution Exhaust mount: 10 mm Torque Solution Exhaust Mount: 12 mm Torque Solution Exhaust Mount: 12 mm Long
Torque Solution Exhaust Mount
Applications:
Universal 10 MM
 
Our exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications:
Universal 12 MM
 
Our exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications:
Universal 12 mm Long
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount: 12 mm Long Torque Solution Exhaust Mount: 15 mm Torque Solution Exhaust Mount: 15 mm Long
MSRP $38.00
MSRP $8.55
MSRP $9.50
Torque Solution Exhaust Mount: 12 mm Long Torque Solution Exhaust Mount: 15 mm Torque Solution Exhaust Mount: 15 mm Long
Torque Solution Exhaust Mount
Applications:
12 mm Long
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications
: Universal 15 mm
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications:
Universal 15 mm Long
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount: 15 mm Long Torque Solution Exhaust Mount Kit: Dodge Neon SRT-4 2003-05 Torque Solution Exhaust Mount Kit: Dodge Caliber 2006-11
MSRP $38.00
MSRP $25.65
MSRP $25.65
Torque Solution Exhaust Mount: 15 mm Long Torque Solution Exhaust Mount Kit: Dodge Neon SRT-4 2003-05 Torque Solution Exhaust Mount Kit: Dodge Caliber 2006-11
Torque Solution Exhaust Mount
Applications: 15 mm Long
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications:
Dodge Neon SRT-4 2003-2005
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications:
Dodges Caliber 2006-2011
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount Kit: Dodge Neon 1995-99 Torque Solution Exhaust Mount Kit: Mazda RX8 Torque Solution Exhaust Mount kit: Scion TC 2005-2010
MSRP $25.65
MSRP $42.75
MSRP $42.75
Torque Solution Exhaust Mount Kit: Dodge Neon 1995-99 Torque Solution Exhaust Mount Kit: Mazda RX8 Torque Solution Exhaust Mount kit: Scion TC 2005-2010
Torque Solution Exhaust Mount Kit
Applications:
Dodge Neon 1995-1999
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount Kit
Applications:
Mazda RX8
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Lifetime Warranty
•Made in USA
Torque Solution Exhaust Mount Kit
Applications: 
Scion TC 2005-2010
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
-Eliminates Exhaust Movment
-Made From high grade polyurethane
-Street and track torture tested
-75A durometer
-Life Time Warranty
-Made in USA
Torque Solution Exhaust Mount kit: Scion TC 2011-13 Torque Solution Exhaust Mount Kit: Chevrolet Cobalt & Cobalt SS 2005-2010 Torque Solution Exhaust Mount kit: Mitsubishi Evolution X 2008-11
MSRP $42.75
MSRP $34.20
MSRP $47.49
Torque Solution Exhaust Mount kit: Scion TC 2011-13 Torque Solution Exhaust Mount Kit: Chevrolet Cobalt & Cobalt SS 2005-2010 Torque Solution Exhaust Mount kit: Mitsubishi Evolution X  2008-11
Torque Solution Exhaust Mount Kit
Applications: 
Scion TC 2011-2013
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
Torque Solution Exhaust Mount
Applications:
Chevy Cobalt & Cobalt SS 2005-2010
 
Our exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kit..
 
-Eliminates Exhaust Movment
-Made From high grade polyurethane
-Street and track torture tested
-75A durometer
-Life Time Warranty
-Made in USA
Torque Solution Exhaust Mount Kit
Applications: Mitsubishi Evolution X  2008-2011
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits.
 
Direct Replacement
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
 
 
 
Torque Solution Exhaust Mount kit: Mitsubishi Evolution X 2008-11 Torque Solution Exhaust Mount: Mitsubishi Torque Solution Exhaust Mount: Mitsubishi
MSRP $42.74
MSRP $16.62
MSRP $9.50
Torque Solution Exhaust Mount kit: Mitsubishi Evolution X  2008-11 Torque Solution Exhaust Mount: Mitsubishi Torque Solution Exhaust Mount: Mitsubishi
Torque Solution Exhaust Mount Kit
Applications: Mitsubishi Evolution X  2008-2011
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits.
 
Direct Replacement Single Side Exhaust
 
•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
 
 

Torque Solution Exhaust Mount
Applications: Mitsubishi

 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 

•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
 

Torque Solution Exhaust Mount
Applications: Mitsubishi

 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits. They fit most cars, please check your car first.
 

•Eliminates Exhaust Movment
•Made From high grade polyurethane
•Street and track torture tested
•75A durometer
•Life Time Warranty
•Made in USA
 
Torque Solution Exhaust Mount Kit: Mazdaspeed 3 2007-2009 Torque Solution Exhaust Mount : Acura RSX 2002-2006 Torque Solution Exhaust Mount Kit: Acura RSX 2002-2006
MSRP $61.74
MSRP $16.62
MSRP $33.24
Torque Solution Exhaust Mount Kit: Mazdaspeed 3 2007-2009 Torque Solution Exhaust Mount : Acura RSX 2002-2006 Torque Solution Exhaust Mount Kit: Acura RSX 2002-2006
Torque Solution Exhaust Mount Kit
Applications: 2007-2009 Mazdaspeed 3

Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kits.
 
Direct Replacement
 
-Eliminates Exhaust Movment
-Made From high grade polyurethane
-Street and track torture tested
-75A durometer
-Life Time Warranty
-Made in USA

Torque Solution Exhaust Mount
Applications: Acura RSX 2002 - 2006
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kit.
 
-Eliminates Exhaust Movement
-Made From high grade polyurethane
-Street and track torture tested
-75A durometer
-Life Time Warranty
-Made in USA
 
Torque Solution Exhaust Mount Kit
Applications: Acura RSX 2002 - 2006
 
Torque Solution exhaust mounts will reduce exhaust movement and vibrations both under extreme racing conditions and daily street driving. Great compliment to any exhaust kit.
 
-Eliminates Exhaust Movement
-Made From high grade polyurethane
-Street and track torture tested
-75A durometer
-Life Time Warranty
-Made in USA
 
Torque Solution Billet Aluminum Passenger Side Engine Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Billet Aluminum Front Engine Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Billet Aluminum Rear Engine Mount: Mitsubishi Evolution VII-IX 2001-2006
MSRP $123.49
MSRP $85.49
MSRP $94.99
Torque Solution Billet Aluminum Passenger Side Engine Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Billet Aluminum Front Engine Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Billet Aluminum Rear Engine Mount: Mitsubishi Evolution VII-IX 2001-2006
Torque Solution Engine Mount
Applications: Mitsubishi  Evolution VII-IX 2001-2006
 
All Torque Solution engine mounts are are made of high grade billet aluminum material, urethane bushings, and steel pins. This is a direct replacement of the OEM passenger side engine mount. This mount can be seen in some of the fastest evo's on the street and at the track! For best results use with Torque Solution's front engine mount, transmission mount, and rear engine mount.
 

 •Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•1000HP+ and 8sec e.t. torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
 
Torque Solution Engine Mount
Applications: Mitsubishi  Evolution VII-IX 2001-2006
 
The Mitsubishi Evolution mount is designed to produce crisper gear shifts by preventing the front end of the engine from pitching up or down, forward and back. Improves traction and reduces wheel hop.All Torque Solution engine mounts are are made of high grade billet aluminum material, urethane bushings, and steel pins. This is a direct replacement of the OEM front engine mount. This mount can be seen in some of the fastest evo's on the street and at the track! For best results use with Torque Solution's passenger side engine mount, transmission mount, and rear engine mount.
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•1000HP+ and 8sec e.t. torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
 
Torque Solution Engine Mount
Applications: Mitsubishi  Evolution VII-IX 2001-2006
 
The Mitsubishi Evolution mount is designed to produce crisper gear shifts by preventing the front end of the engine from pitching up or down, forward and back. Improves traction and reduces wheel hop. All Torque Solution engine mounts are are made of high grade billet aluminum material, urethane bushings, and steel pins. This is a direct replacement of the OEM rear engine mount. This mount can be seen in some of the fastest evo's on the street and at the track! For best results use with Torque Solution's passenger side engine mount, transmission mount, and front engine mount.
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•1000HP+ and 8sec e.t. torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
 
Torque Solution Billet Aluminum 5 Speed Transmission Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Billet Aluminum 6 speed Transmission Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Rear Differential Mount Inserts: Mitsubishi Evolution VIII-IX 2003-2006
MSRP $147.24
MSRP $147.24
MSRP $61.74
Torque Solution Billet Aluminum 5 Speed Transmission Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Billet Aluminum 6 speed Transmission Mount: Mitsubishi Evolution VII-IX 2001-2006 Torque Solution Rear Differential Mount Inserts: Mitsubishi Evolution VIII-IX 2003-2006
Torque Solution Transmission Mount
Applications: Mitsubishi  Evolution VII-IX 2001-2006
 
All Torque Solution engine mounts are are made of high grade billet aluminum material, urethane bushings, and steel pins. This is a direct replacement of the OEM transmission mount. This mount can be seen in some of the fastest evo's on the street and at the track! For best results use with Torque Solution's passenger side engine mount, front engine mount, and rear engine mount.
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•1000HP+ and 8sec e.t. torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
 
 
Torque Solution Transmission Mount
Applications: Mitsubishi Evolution VII-IX 2001-2006
 
All Torque Solution engine mounts are are made of high grade billet aluminum material, urethane bushings, and steel pins. This is a direct replacement of the OEM 6 SPEED transmission mount. This mount can be seen in some of the fastest evo's on the street and at the track! For best results use with Torque Solution's passenger side engine mount, front engine mount, and rear engine mount.
 
 
•Eliminates wheel hop / traction loss
•Improved 60fts / e.t's
•Made out of lightweight 6061-T6 billet aluminum
•1000HP+ and 8sec e.t. torture tested
•Black anodized / Torque Solution Laser engraved
•75A durometer bushings
•Life Time Warranty
•Made in USA
 
Torque Solution Rear Differential Mount Inserts
Applications: Mitsubishi  Evolution VIII-IX 2003-2006

These Solid Polyurethane bushings are much harder compared to the OEM units. By replacing them with these harder Polyurethane units you are able to get rid of the unwanted slop and flexing of the stock units which allows for the power to go into rotating the tires, instead of flexing the rubber. Giving you better feedback, sharper response, more predictability on throttle input, along with eliminating annoying clunking during hard shifts.

-Eliminates the " CLUNK " when shifting hard
-Reduces wheel hop / traction loss
-Improved 60fts / e.t's
-1000HP+ and 8sec e.t. torture tested
-75A durometer bushings
-LifeTime Warranty
-Made in USA
   
 
We accept Mastercard, Visa, American Express, and Discover